BCM Community
Bus Discussion => Bus Topics ( click here for quick start! ) => Topic started by: Red Rider on October 22, 2013, 03:23:24 PM
-
My Spicer 4 speed has been named officially worn out. I'd like to find one that has a known history, preferably a "take-out". I'm in Southern Utah so anything in the west would be just wonderful.
I'm well aware that these units are becoming harder to find however this board continually bails folks out when they have special needs. Any help would be appreciated.
-
Ok you GM people will a 4 speed from a 4905A work for Mikey's 4106 ?
-
Cliff: I think all 4905 had a wet clutch. Because Mike's input is out??? What type of input shaft bearing was in Jim old engine, Was it replace with a dry bearing for the 06.
Mike: there is two 06 for parts where you just were a week ago!!! Call Robert about them.
Bruce
-
Time for Allison V730! Good Luck, TomC
-
Hey Tom;
You may not believe it but I enjoy the 4spd.
Clifford;
I can't believe you've forgotten something. When we where doing the engine at your place I had some "time-out" because this current engine had a wet clutch and we had to jump through hoops to change everything over. The tranny that I have had the same abuse that old engine did so you can figure there is not a lot to work with.
Bruce;
I thought of that but how in he word would I get one out of any of his buses?
Thanks everybody.
-
It was a wet clutch Bruce the one I removed from a 4905 was converted over to a dry clutch my understanding is the input was the only change because the wet clutch uses more splines than the dry clutch and he could not find a clutch plate with matching splines
Don and Cary have 730 listed on the BNO for 900 bucks if Mikey wants to go that direction I didn't forget Mike I was still typing and see that $#!% on my trailer lol tell us what you mean by worn out ? while you are here is there a Roy Rammer in the GM club and send me Halls phone # thanks
good luck
-
Dan and I pulled the trans out today because there was a fluid leak coming out of the main drive into the bell housing. When we got it out we find almost 1/2 " of play and pieces of the front carrier bearing fell out in my hand. If the main shaft and bearings are in that condition I figure the rest is about the same. Finding the correct parts and the cost of them seems to me not as practical as a replacement unit --- of course the condition and history is most important.
-
Do a bearing job and run that puppy bearing are not hard to find for that transmission any bearing house will have those or can order if you buy a used one I would replace all the bearing before I installed it anyway those transmissions are not hard to rebuild
-
Mike: 15 years ago Don Matthews sold Gary's 4 speed to a friend, He (friend) & I pull it out a Gary's in the dirt, loaded it up haul it to a truck stop in Portland to pull and replace his bad 4 speed and then came home, all in the dirt. Gary came home went to move his bus to find he need to find a tran's for his. Don thought he need a VS2!!! You should call Robert & see if he might sell you one. Also you might try Dick Grasso in Golden Valley.
Bruce
-
Thanks again Clifford.
-
If the gears are OK, replacing the bearings should not be too hard. I doubt that any bearing house can cross to the old GM part numbers but the bearing will have numbers on them that they can use..
-
You don't need numbers all good bearing supply use high tech measuring equipment now when through measuring it puts the bearing number on the computer screen technology at it's best
-
I'd be surprised if the bearings in that trans didn't all say Timken on them followed by a bearing number. Should be able to get them anywhere unless they were captive to Spicer. The tricky stuff might be hard parts like sliding clutches but if it isn't jumping out of any gear on accel or decel they are likely OK.
If you like the 4 spd go with a re-bearing and input shaft and drive it another million miles. If you buy a used trans then that is all you have, a used trans and you already have one of those. The one that have you at least know/have some history with.
Kevin
-
As usual the board has come through will a lot of good info. I'm reluctant to go into the trans however, the issue of shims, spacers, possible shafts and gaskets make me nervous. Aligning that "v" is another concern I have. A straight box that is not model specific is one thing, but I hate jumping into something that I'm aware I know nothing about.
Thanks again.
-
Before I gave up Mikey I would disassemble the transmission you have that is a simple transmission no sycno gears just sliders and forks if the transmission was not knocking from teeth missing go for it tear it apart you have nothing to lose except 1 day with Dan
If the bearing surface and seat on the main shaft is ok and if bad they can welded and turned the rest is easy? at our age how much longer do except the bus or us to last ::)
-
Aligning that V? You don't need to change shims just to take apart and replace that front bearing assy. Those trans are pretty simple inside and parts are large. They aren't delicate like a car or truck trans. Normal wear isn't going to effect reliability. You can make gaskets or use silicone in some places. Just follow repair manual for taking it apart. Only disassemble enough to replace front bearing and turn over and flush out any debris. If you don't feel comfortable doing it yourself, Find an independant place that repairs truck trans. Just tell him you want it repaired, not rebuilt.
-
I thought it would be polite to post a follow-up since so many of you folks provided assistance.
After further investigation we found the main drive gear missing approx 50% of it's teeth. The front carrier bearing as fused to the shaft and took 50,000 lbs to press it off. The race is "welded" to the case. Half of the rollers from the inner bearing was made into shrapnel and was on the drain plug magnet. It looks like the idea of putting in some replacement bearing went south.
I called Luke to see what his opinion might be and he felt that I should look for a replacement trans.
Still looking for an 06, V drive, four speed.
Thanks again.
-
Mike now you know for sure
good luck
-
The double clutching method may be required. LOL
-
Boomer;
Does that mean I'm supposed to push the clutch in when I shift? LOL
-
Mikey you need to stop driving the bus up on the lowboy let the wrecker driver use the winch how do tear up a transmission that bus is always riding every time I see it ::)
-
Also, he neads to make sure the trany out of gear when the big wrecker draging it out of the sand...lol
-
Hey Red Rider I have a 4106 4 speed with a 1 year old clutch and a 8v71 all on a cradle mouted on a dolly to roll in a engine compartment. The trans was gone thru. The needle bearings alone were over $300.00 dollars. Come and get it $1000.00 olebusman ps The clutch was over $1000.00 complete with flywheel face insert
-
Ted Campbell probably has one.
-
Thank you everybody. I have committed to buying a dry clutch 06 set up. We found it in Southern AZ. The seller has a fine reputation and comes highly recommended. He is parting out his Bus and the folks who bought the engine are very pleased.
There are no new 06 trannys around so this will have to work.
Matt: Obviously I had the clutch in. How else can you bury a 06 all the way to the axle in the sand?
-
As far as the sand goes I think it was the GPS not the driver. I mean who knew there was a river there.
LeRoy
-
OK Leroy, be nice.
-
Who ever knew AZ was in CA lol you will never live that down Mikey
-
Hey Clifford,
A wise man once said "you get what you deserve". I really think it all your fault. If I hadn't been going to visit you I wouldn't have run into the Colorado River. :)
With that logic I should run for congress.