Author Topic: Broken wheel stud in Springfield MO  (Read 4412 times)

Offline thomasinnv

  • Derrick Thomas
  • Hero Member
  • *****
  • Posts: 1492
  • I may be nuts, but only for buses
Broken wheel stud in Springfield MO
« on: June 14, 2018, 12:18:29 PM »
I was about 20 miles south of Springfield just loping along at 60 on a smooth straight highway when i heard a loud thud from the right front corner. Immediately pulled off to investigate and found a missing wheel stud on the right steer. Limped into a fleetpride and they now have 10 right hand and 10 left hand studs on a fedex truck. Should be back on the road tomorrow afternoon. First thing that came to mind was the fella that had his drive wheels come off a few weeks ago. His misfortune prompted me to not even consider just replacing the broken stud and the adjacent ones on either side of it like some had suggested. Just not worth the risk over a couple hundred bucks.

Sent from my SM-G930T using Tapatalk
Some are called, some are sent, some just got up and went.

1998 MCI 102-DL3
Series 60 12.7/Alison B500
95% converted (they're never really done, are they?)

Offline buswarrior

  • Hero Member
  • *****
  • Posts: 6564
  • the old one: '75 MC8 with an 8V71 HT740
Re: Broken wheel stud in Springfield MO
« Reply #1 on: June 14, 2018, 01:11:10 PM »
Proudly spend the money, and I will proudly cheer you on!

And stand ready to beat with a tire iron, anyone who tries to gun the fasteners on ever again.

happy coaching!
buswarrior
Frozen North, Greater Toronto Area
new project: 1995 MCI 102D3, Cat 3176b, Eaton Autoshift

Offline Lin

  • Hero Member
  • *****
  • Posts: 5531
  • 1965 MC-5a
Re: Broken wheel stud in Springfield MO
« Reply #2 on: June 14, 2018, 01:13:01 PM »
I guess this would go under the category, "What is peace of mind worth?".
You don't have to believe everything you think.

Offline eagle19952

  • Hero Member
  • *****
  • Posts: 4039
Re: Broken wheel stud in Springfield MO
« Reply #3 on: June 14, 2018, 01:50:31 PM »
I guess this would go under the category, "What is peace of mind worth?".

1/2 inch drive speed handle on :)



followed by:
Donald PH
1978 Model 05 Eagle w/Torsilastic Suspension,8V71 N, DD, Allison on 24.5's 12kw Kubota.

Offline luvrbus

  • Hero Member
  • *****
  • Posts: 26049
Re: Broken wheel stud in Springfield MO
« Reply #4 on: June 14, 2018, 04:11:46 PM »
It depends on the individual,replacing the broken stud along with 2 adjoining studs (1 up and 1 down) is a DOT ruling and I am ok with it lol I would rather have 7 studs made in the USA than 10 made in China.

 I refuse to use studs made in China even if the made in the USA studs do cost 3 times as much   
Life is short drink the good wine first

Offline richard5933

  • Hero Member
  • *****
  • Posts: 3963
Re: Broken wheel stud in Springfield MO
« Reply #5 on: June 14, 2018, 04:17:33 PM »
I agree with replacing them all if possible. May not be necessary, but my peace of mind is worth more than the studs cost.
Richard
1974 GMC P8M4108a-125 Custom Coach "Land Cruiser" (Sold)
1964 GM PD4106-2412 (Former Bus)
1994 Airstream Excella 25-ft w/ 1999 Suburban 2500
Located in beautiful Wisconsin

Offline chessie4905

  • Hero Member
  • *****
  • Posts: 7101
Re: Broken wheel stud in Springfield MO
« Reply #6 on: June 14, 2018, 04:23:52 PM »
I hope he didn't  tighten everything back up with a big @$# impact wrench. ???
GMC h8h 649#028 (4905)
Pennsylvania-central

Offline windtrader

  • Hero Member
  • *****
  • Posts: 2427
Re: Broken wheel stud in Springfield MO
« Reply #7 on: June 14, 2018, 05:09:48 PM »
Get 80 then maybe you'll sleep better. I wouldn't as I'd never hear the end of spending a grand on wheel studs and nuts. lol
Don F
1976 MCI/TMC MC-8 #1286
Fully converted
Bought 2017

Offline luvrbus

  • Hero Member
  • *****
  • Posts: 26049
Re: Broken wheel stud in Springfield MO
« Reply #8 on: June 14, 2018, 05:18:06 PM »
Get 80 then maybe you'll sleep better. I wouldn't as I'd never hear the end of spending a grand on wheel studs and nuts. lol


Lol a year later and I still get the question by a certain female  :D
Life is short drink the good wine first

Offline thomasinnv

  • Derrick Thomas
  • Hero Member
  • *****
  • Posts: 1492
  • I may be nuts, but only for buses
Re: Re: Broken wheel stud in Springfield MO
« Reply #9 on: June 15, 2018, 05:16:56 AM »
It depends on the individual,replacing the broken stud along with 2 adjoining studs (1 up and 1 down) is a DOT ruling and I am ok with it lol I would rather have 7 studs made in the USA than 10 made in China.

 I refuse to use studs made in China even if the made in the USA studs do cost 3 times as much   
Had it been a case of being twisted off during lug nut installation I would probably have been satisfied with replacing the 3, but becuase it came off while just rolling down the highway and there were visible signs of damage to several other studs from possible over tightening in the past, I feel better about carting my family around with all the new studs.

Some of you might remember the fiasco I went thru a few years ago with having the engine and trans rebuilt in my mc8. After dumping literally tens of thousands of dollars into it I ended up selling it for about scrap value becuase I no longer had any confidence in it. Every time I fired it up I was wondering how far it would take me before it blew apart. That's not a good way to travel. When I put my family in a rig, no matter what it is, I have to have some level of confidence that it will get us safely to our destination. If I don't have that, then it has to go.

Sent from my SM-G930T using Tapatalk
Some are called, some are sent, some just got up and went.

1998 MCI 102-DL3
Series 60 12.7/Alison B500
95% converted (they're never really done, are they?)

Offline luvrbus

  • Hero Member
  • *****
  • Posts: 26049
Re: Broken wheel stud in Springfield MO
« Reply #10 on: June 15, 2018, 05:54:34 AM »
They probably were over tighten if there were signs on the others I would I have went with 10 in that case,the 1-1/8 stud on the stud pilot wheel is a tough stud to break they don't break on their own, or do you have hub pilot wheels they break easier 
Life is short drink the good wine first

Offline thomasinnv

  • Derrick Thomas
  • Hero Member
  • *****
  • Posts: 1492
  • I may be nuts, but only for buses
Re: Broken wheel stud in Springfield MO
« Reply #11 on: June 15, 2018, 07:03:44 AM »
They are stud pilot

Sent from my SM-G930T using Tapatalk
Some are called, some are sent, some just got up and went.

1998 MCI 102-DL3
Series 60 12.7/Alison B500
95% converted (they're never really done, are they?)

Offline luvrbus

  • Hero Member
  • *****
  • Posts: 26049
Re: Broken wheel stud in Springfield MO
« Reply #12 on: June 15, 2018, 07:12:33 AM »
Some tire monkey really hammered on it with a 1 inch I/R gun with a good air supply to damage those,better check the wheels real close  
Life is short drink the good wine first

Offline thomasinnv

  • Derrick Thomas
  • Hero Member
  • *****
  • Posts: 1492
  • I may be nuts, but only for buses
Re: Re: Broken wheel stud in Springfield MO
« Reply #13 on: June 15, 2018, 07:39:35 AM »
Some tire monkey really hammered on it with a 1 inch I/R gun with a good air supply to damage those,better check the wheels real close  
There is some evidence in the nut wells (some galling) that they were overtightened, but no cracks.

Sent from my SM-G930T using Tapatalk
Some are called, some are sent, some just got up and went.

1998 MCI 102-DL3
Series 60 12.7/Alison B500
95% converted (they're never really done, are they?)

Offline Ed Hackenbruch

  • Hero Member
  • *****
  • Posts: 2984
Re: Broken wheel stud in Springfield MO
« Reply #14 on: June 15, 2018, 08:13:29 AM »
Did you check the back side of the wheel?  I had a fine crack on the back side of both of my front wheels from being over torqued by tire shops.  Cracks couldn't be seen on the front side and just barely showed under the paint on the back side but were definitely there. New wheels all around after that and nobody touched them but me while we still had the bus.
Used to own a 1968 MCI 5A and a 1977 5C.

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal